Skip to main content

How to troubleshoot your NT-1228BL Barcode Scanner

Fix common NT-1228BL barcode scanner issues — dead battery, failed scans, pairing problems, and wrong characters. Includes a quick reference for every LED and beep pattern.

Written by Euri

This article covers the most common issues with the NT-1228BL barcode scanner and how to fix them — dead or dying batteries, scans that don't appear on the Sunmi, pairing problems, and wrong characters. It also has a quick reference for every LED and beep pattern.

NETUM NT-1228BL Barcode Scanner with Stand

When to use:

  • Your scanner beeps but nothing appears on the Sunmi screen.

  • The scanner is behaving oddly and you want a fresh start.

  • You want to know what a specific LED color or beep pattern means.

  • You need to charge the scanner or you're not sure how low the battery is.


What the lights and beeps mean

Lights:

  • Red light on: the scanner is charging.

  • Green light on: the scanner is fully charged.

  • Blue light flashes briefly when it beeps: normal activity.

  • Blue light solid or flashing continuously: Bluetooth mode is active.

  • Blue light off: the scanner is in 2.4G (USB dongle) mode or wired USB mode.

Beeps:

  • One short beep right after a scan: the scan was successful.

  • Two beeps during a scan: low battery. Charge soon.

  • Three beeps and a flashing LED: the scanner isn't connected to a device. Re-pair using the steps in the setup article.

  • Five beeps and it shuts off: battery is dead. Plug it in and let it charge for at least 30 minutes before trying again.
    ​


How to charge the scanner

  • Plug the included OEM USB cable into the scanner's charging port.

  • Use a 5V or lower adapter. Anything higher will damage the scanner.

  • While charging the red LED stays on. When it's fully charged, the green LED stays on.

  • If the scanner was completely dead, give it at least 30 minutes on the charger before you try to use it.

  • When you hear two beeps during a scan, the battery is low. Plug it in soon so it doesn't die mid-shift.
    ​


Factory reset the scanner

Scan the Restore Factory Default barcode. Use this when:

  • The scanner is behaving strangely.

  • You're moving the scanner to a different Sunmi tablet and want to re-pair.

  • You tried every other fix below and nothing worked.
    ​


After a factory reset, run through the setup article again to re-pair and re-configure.
​


Troubleshooting

  • The scanner doesn't beep at all.
    It's not charged. Plug in the USB cable, confirm the red LED turns on, and give it 30 minutes.
    ​

  • Three beeps and a flashing LED.
    The scanner isn't connected to a device. Go back to the setup article and re-pair using your preferred connection mode.
    ​

  • Five beeps and it shuts off.
    Dead battery. Charge for at least 30 minutes before trying again.
    ​

  • Two beeps every time you scan.
    Low battery warning. Scans still work, but plug it in soon.
    ​

  • Scanner beeps but nothing appears on the Sunmi.
    Make sure the cursor is in a text field first. If it still doesn't work, re-scan Trigger Mode and CR Terminator from the setup article, then check the Sunmi's Scan code and Keyboard settings.
    ​

  • Scans go into the wrong field or add extra characters.
    Factory reset the scanner and run through the setup steps again.
    ​

  • Garbled or wrong characters when scanning.
    The keyboard language is set wrong. Scan the America EN Keyboard barcode in the Quick Start Guide.
    ​

  • Scanner used to work but now doesn't.
    Factory reset, then re-pair using your preferred connection mode.
    ​

  • Still stuck?
    Text our Support team.


Need assistance?

Feel free to text our Cents Support team at 888-302-8809.

Did this answer your question?